Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
Everyone will have their personal piece of advice involving Installing A Bathtub.
Installing a bath tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently available, the task can move speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the task and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is far better to take into consideration employing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a new tub in your bathroom if you have already bought a new tub and don't need to alter the plan of your previous water system pipes.
Your tools and product list must make up the following:
Preparing for the Installment
To start with, the sustaining framework provided with the bath should be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of the two taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the tub up until the level reads degree.
To set up taps, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Turn on the water supply and inspect all joints as well as new pipework for leaks as well as tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait up until the tub has been made use of a minimum of once as this will settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall surface between the bathroom and also the tiling, resulting in issues with wetness and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and installations. They are sold in tubes and cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealant can fracture relatively very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the marketplace. It is advisable to fit the tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very intrigued by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you appreciated the new blog post. Those who enjoyed reading our article plz make sure you remember to share it. We take joy in reading our article about How to Install a Bathtub Yourself.
Damage control? Call us. Report this page